Signal box interior kit for OO layouts (4mm /1ft)

Add an interior to your signal box for extra realism!

The kit includes 36 levers in three frames of 12 each. Each lever can be fitted in the forward or back positions to your own preference.

Also in the set is the shelf, block instruments, bells, level crossing wheel with mechanism detail, an armchair, wall clock, cabinet, stove with chiney pipe, and a hand coal shovel.

If you have the Severn Models signal box D3, you only need two frames of 12 levers, as this box had 24 levers. Extras are included for those modelling larger boxes.

As a guide to size for fitting into other buildings, the assembled model in the photos is 82x36mm on the floor with all 36 levers and the crossing wheel at the end.

(The floor and walls in the photos are for illustration purposes and are not included in this kit).

Supplied as a flat brass etch kit, requiring assembly and painting.

A kit to build four Great Western Railway bench seats.

The GWR had very distinctive seating for their platform benches - each leg casting has the GWR roundel in relief detail, which is neatly represented in this kit.

The kit builds two benches for 2 leg castings, and two benches for 3 leg castings, as per the set in the photos.

Supplied as a flat packed brass etch kit, requiring assembly and painting.

The 'official' paint scheme was apparently that the entire bench would be chocolate brown, however over time the logo began to be picked out in creamy white which then became the norm.

Add realism with some scale furniture!

Includes beds, chairs, table, wardrobe, desk, dressing table & stool, plus finer detailing with plates, books, files and a jewellery box!

Many of the items fold up from one piece of brass, so minimising the assembly required.

Supplied as a flat packed brass fret, requiring assembly and painting.

This kit features six ladders of various types.

Two long straight ladders (cut off to whatever length you wish), about 112mm long, and 4.8mm wide.

Two wall/roof ladders, with fold-back fixing brackets and handrails at the top.

Two general purpose tapered ladders.

Supplied as a flat brass fret kit, requiring assembly and painting.

A kit to build a typical sidings hut, as would have been commonly seen in railway yards and storage sidings.

The footprint of the main building is 50 x 50mm, then the lean-to store is 35 x 31mm.

Supplied as a flat brass etch kit, requiring assembly and painting.

A kit to build a sidings workshop, as would be typically seen in rail yards and storage sidings.

Alternate uses might be storage, offices or a workers canteen area.

Main building footprint is 95 x 52mm, and the lean-to store is 20 x 23mm.

Supplied as a flat brass etch kit, requiring assembly and painting.

Add detail to roads, yards and pavements by adding some drainage!

Includes rectangular and round inspection covers, and road drain grids. Just snip them from the fret and let them into your road surfaces.

A kit to build a small stables.

A brick built stables with slate/tile roof, and split doors. Set the doors open or closed at your choice.

Overall size approx 90 x 50mm footprint.

Supplied as a flat brass fret kit, requiring assembly and painting.

Add realism with some scale furniture!

Includes chairs, table, office desk, filing cabinets, bookcase, drawing board, stools, books, box file, papers and drawing instruments.

Many of the items fold up from one piece of brass, so minimising the assembly required.

Supplied as a flat packed brass fret, requiring assembly and painting.

A kit to make two ground point levers, suitable for 4mm / OO gauge layouts.

Each lever includes a bell crank and clevises, so they can be made functional if you wish.

Brass wire is also included for making the pivot pins and rods, 0.3mm diameter.

They are in scale at 1:76. Overall height of a lever is about 19mm. The base 'box' is approx 8.5mm x 5.5mm.

Supplied as a flat packed brass kit, requiring assembly and painting.